Material No.: N 06455
Description
|
| ||||||||||||||||||||
|
Chemical Composition
C | Mn | P | S | Cr | Mo | Si | Co | Fe | Ni | Ti | Cu | ||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
N 06455 | Min % | 14,00 | 14,00 | remainder | |||||||||
Max % | 0,015 | 1,00 | 0,040 | 0,030 | 18,00 | 17,00 | 0,08 | 2,00 | 3,00 | remainder | 0,70 | ||
ASTM B 622 | |||||||||||||
2.4610 | Min % | 14,00 | 14,00 | balance | |||||||||
Max % | 0,015 | 1,00 | 0,025 | 0,015 | 18,00 | 17,00 | 0,08 | 2,00 | 3,00 | balance | 0,70 | 0,50 | |
(Key to Steel 2010) | |||||||||||||
alloy C-4 | Min % | 14,00 | 14,00 | remainder | |||||||||
Max % | 0,015 | 1,00 | 0,040 | 0,030 | 18,00 | 17,00 | 0,08 | 2,00 | 3,00 | remainder | 0,70 |
Physical properties
Property | Value |
---|---|
Density: lb/in.3 | 0,314 |
Hardness: HB | <=320 |
Permeability at 20°C/68°F | <1,01 |
Temperature T °C/F (°C/F) | Specific heat J / kgK (Btu / lb °F) | Thermal conductivity W/mK (Btu·in / ft2·h·°F) | Electric resistance µΩ · cm (Ω circ mill / ft) | Modulus of elasticity kN/mm2 (103 ksi) | Expansion rate from 70°F bis T 10-6 / K (10-6 / °F) |
---|---|---|---|---|---|
20 / 68 (93 /200) | 408 / 0,097 (101) | 10,1 (70) (79) | 124 (75) (75) | 211 (30,8) (30,2) | (6.0) |
100 / 212 | 426 | 11,4 | 125 | 207 | 10,9 |
200 /392 (204/400) | 448 (0,107) | 13,2 (92) | 126 ( 76) | 202 (29,3) | 11,9 ( 6.6) |
300 / 572 (316/600) | 465 (0,111) | 15,0 (106) | 127 (76) | 195 (28,3) | 12,5 (7.0) |
500 / 932 (538 / 1000) | 490 (0,118) | 18,4 (133) | 129 (78) | 181 (26,2) | 13,2 (7,4) |
600/1112 (649/ 1200) | 502 (0,121) | 20,5 (149) | 132 (80) | 175 (25) | 13.6 (7,7) |
700 / 1292 (760/ 1400) | 512 (0,124 ) | 22,6 (152) | 135 (82) | 168 (23,7) | 140 (8.0) |
800 / 1432 (871/1600) | 522 | 24,8 | 138 | 158 (22,2) | 15.1 (8.7) |
. | . |
Mechanical properties (20°C / 68°F)
Yield strength (0,2% offset) min,ksi | 40-45 (280-310) | ||
---|---|---|---|
Yield strength ,ksi | 46-49 | ||
Tensile strength min.ksi | 100 (690) | ||
Elongation A 5 (%) | 40 | ||
ISO V Notched impact strength at -196°C/-320.8°F (J/cm2) | >=120 | ||
Remarks |
Temparature information
Application area | ||
---|---|---|
Operation temperature | -321 ºF to 842 ºF | scaling resistance in air 2012°F |
Explanation report | in solution annealed state |
Solution heat treatment | ||
---|---|---|
Working temperature | 1922 ºF to 2012 ºF | preferably 2000°F |
Explanation report | water cooling | |
Processing informations | easy to weld/process when solution annealed, especially good machining properties |
Solution heat treatment | ||
---|---|---|
Working temperature | 2156 ºF to 1652 ºF | |
Explanation report | water or air cooling | |
Processing informations | following heat treatment to achieve optimal properties is adviced |
Standards / information
Standards | Desciption |
---|---|
ASTM B 366 | Standard Specification for Factory-Made Wrought nickel and nickel alloy fittings |
ASTM B 574 | Standard Specification for LOW-Carbon Nickel-Molybdenum Alloy Rod |
ASTM B 575 | Standard Specification for Plate, Sheet and Strip |
ASTM B 619 | Standard Spezifikation for Welded Nickel and Alloy Pipe |
ASTM B 622 | Standard Specification for Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube |
ASTM B 626 | Standard Specification for Welded Nickel and Nickel-Cobalt Alloy Tube |
DIN 17744 (2002/09) | nickel-forgeable alloy with molybdenum and chrome |
DIN 17750 (2002/09) | ribbons and sheet metal out of nickel with nickel-wrought alloy properties |
DIN 17751 (2002/09) | tubes out of nickel with nickel-wrought alloy properties |
DIN 17752 (2002/09) | rod made from nickel with nickel-wrought alloy properties |
DIN 17753 (2002/09) | wire out of nickel with nickel-wrought alloy properties |
VdTÜV-Werkstoffblatt 424 | extremely corrosion resistant alloy, NiMo16Cr16Ti, material-nr. 2.4610; ribbon, sheet metal, forging, rod, seamless pipe |
Process information
Cold forming | good when annealed, shows tendency to cold work hardening; requires solution annealing after forming larger than 15% |
---|
Chip removing process | - preferably in annealed state, due to tendency to cold work hardening - slow cutting velocity and cutting tools in constant contact |
---|
Welding | |
---|---|
- Material classification acc. CEN ISO/TR 15608 | 44 |
- Type | WIG |
Main fields of application
Details of application | |
---|---|
Certifications | |
Chemical Industry | Chlorierungsanlagen;; Reaktoren |
waste incineration plants | Müllverbrennunsanlagen |
Rauchgasentschwefelungsanlagen(REA) | |
Fertiliser industry | Düngemittelherstellung |
Power engineering |
Range of products
Product type | Product |
---|---|
Plates / Sheets | plates/sheets plate/sheet cuts |
Rotating components | fittings from barsteel |
Fittings | welded elbows welded reductions Welded T-pieces |
Flanges / Collars / Flared tube ends | flared tube end collars various flanges (weld neck flange,blind flange etc.) |
Pipes / Tubes | welded pipes/tubes welded square pipes/tubes |
Bar steel | flat steel section steel round bar steel hexagon steel |
Liability exclusion
All aforementioned specifications serve as a general orientation and have to be reviewed depending on the conditions of use.(c) 2012 M. Woite GmbH, Postbox, D-40671 Erkrath | Phone +49 (211) 24 40 91 - Fax +49 (211) 24 92 28 | www.m-woite.com - woite@woite-edelstahl.com