Material No.: AISI 405
Description
|
|
Chemical Composition
| C | Si | Mn | P | S | AL | Cr | Ni | N | ||
|---|---|---|---|---|---|---|---|---|---|---|
| AISI 405 | Min % | |||||||||
| Max % | ||||||||||
| 1.4724 | Min % | 0,70 | 0,70 | 12,00 | ||||||
| Max % | 0,12 | 1,40 | 1,00 | 0,040 | 0,015 | 1,20 | 14,00 | |||
| (Key to steel 2010) | ||||||||||
| S 44600 | Min % | 23,00 | ||||||||
| Max % | 0,20 | 1,00 | 1,50 | 0,040 | 0,030 | 27,00 | 0,75 | 0,25 | ||
| ASTM A268 (UNS S44600) | ||||||||||
Physical properties
| Property | Value |
|---|---|
| Density: kg/dm3 | 7,7 |
| Hardness: HB | <=192 |
| magnetizable | yes |
| Temperature T °C/F (°C/F) | Specific heat J / kgK (Btu / lb °F) | Thermal conductivity W/mK (Btu·in / ft2·h·°F) | Electric resistance µΩ · cm (Ω circ mill / ft) | Modulus of elasticity kN/mm2 (103 ksi) | Expansion rate from 70°F bis T 10-6 / K (10-6 / °F) |
|---|---|---|---|---|---|
| 20 / 68 | 500 (--) | 21 (--) | 200 (--) |
| Temp. | Creep strain limit | Creep strain limit | Creep rupture strength | Creep rupture strength | Creep rupture strength |
|---|---|---|---|---|---|
| °C / °F | 1000 h | 10 000h | Rp 1,0 (MPa) (geglüht) | Rp 1,0 (MPa) (geglüht) | |
| 600 /1112 | 27,5 | 35 | |||
| 800 /1472 | 3,7 | 4,3 | |||
| 900 / 1652 | 1,8 | 1,9 | |||
| 1000 / 1832 | 0,5 |
Mechanical properties (20°C / 68°F)
| 0,2%Yield strength Rp0,2N7mm2/ksi | 250 / 36,2 | ||
|---|---|---|---|
| Tensile strenght Rm N/mm2/ksi | 450-650/65,2-94,2 | ||
| Elongation A5 (%) | <=15 | ||
Temparature information
| Application area | ||
|---|---|---|
| Operation temperature | ºF to 1562 ºF | by air to ca 1472°F (resistant to scaling) |
| soft annealing | ||
|---|---|---|
| Working temperature | 1472 ºF to 1580 ºF | |
| Solution heat treatment | ||
|---|---|---|
| Working temperature | 2012 ºF to 1472 ºF | |
| annealing | ||
|---|---|---|
| Working temperature | 1472 ºF to 1562 ºF | afterwards: Ferrit |
Standards / information
| Standards | Desciption |
|---|---|
| ASTM A 276 | Rods and cross-sections made of stainless and heat-resistant steel |
Process information
| Chip removing process | good machinability |
|---|
| Welding | |
|---|---|
| - Add. material | 1.4502,1.4723,1.4773,1.4820 |
Main fields of application
| Details of application | performs well under sulfidising conditions |
|---|---|
| Certifications | |
| petrochemical industry | |
| industral furnace engineering | |
| Steam boiler construction |
Range of products
| Product type | Product |
|---|---|
| Processing / Construction | from sheets |
| Plates / Sheets | plates/sheets plate/sheet cuts |
| Fittings | welded elbows welded reductions Welded T-pieces seamless elbows seamless reductions seamless T-pieces |
| Flanges / Collars / Flared tube ends | various flanges (weld neck flange,blind flange etc.) |
| Pipes / Tubes | welded pipes/tubes seamless pipes/tubes |
| Round bar | peeled |
| Bar steel | section steel round bar steel |
Liability exclusion
All aforementioned specifications serve as a general orientation and have to be reviewed depending on the conditions of use.(c) 2012 M. Woite GmbH, Postbox, D-40671 Erkrath | Phone +49 (211) 24 40 91 - Fax +49 (211) 24 92 28 | www.m-woite.com - woite@woite-edelstahl.com