Material No.: 2.4663
Description
|
| ||||||||||||||||||||||
|
Chemical Composition
C | Mn | P | S | Cr | Mo | Si | Co | Fe | Ni | Cu | AL | Ti | B | ||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
2.4663 | Min % | 0,05 | 20,00 | 8,50 | 11,00 | bal. | 0,70 | 0,20 | |||||||
Max % | 0,10 | 0,20 | 0,010 | 0,010 | 23,00 | 10,00 | 0,20 | 14,00 | 2,00 | bal. | 0,50 | 1,40 | 0,60 | 0,006 | |
(Key to Steel 2010) | |||||||||||||||
alloy 617 N 06617 | Min % | 0,05 | 20,00 | 8,00 | 10,00 | 44,50 | 0,80 | ||||||||
Max % | 0,15 | 1,00 | 0,015 | 24,00 | 10,00 | 1,00 | 15,00 | 3,00 | 0,50 | 1,50 | 0,60 | 0,006 | |||
ASTM B167 |
Physical properties
Property | Value |
---|---|
Density: lb/in.3 | 0,303 |
Permeability at 20°C/68°F | --- |
Temperature T °C/F (°C/F) | Specific heat J / kgK (Btu / lb °F) | Thermal conductivity W/mK (Btu·in / ft2·h·°F) | Electric resistance µΩ · cm (Ω circ mill / ft) | Modulus of elasticity kN/mm2 (103 ksi) | Expansion rate from 70°F bis T 10-6 / K (10-6 / °F) |
---|---|---|---|---|---|
20 / 68 (93 / 200) | 400 (0104) | 13,4 (101) | 122 (748) | 212 (30) | (6,4) |
200 /392 (204 / 400) | 465 (0,111) | 16,3 (113) | 126 (7579 | 200 (29,0) | 12,6 (7,0) |
400/752 (427 / 800) | 515 (0,124) | 19,3 (137) | 128 (770) | 188 (26,9) | 13,6 (7,6) |
600 /1112 (649 / 1200) | 565 (0,137) | 22,5 (161) | 131 (793) | 173 (24,6) | 14,0 (8,0) |
800 /1472 (871 / 1600) | 615 (0,150) | 25,5 (185) | 134 (808) | 157 (21,9) | 15,4 (8,7) |
900 / 1652 (982 /1800) | 645 (0,1579 | 27,1 (197) | 135 (824) | 149 (29,4) | 15,8 (9,0) |
1000 / 1832 | 665 | 28,7 | 138 | 139 | 16,3 |
Mechanical properties (20°C / 68°F)
Yield strength Rp0,2 (MPa) | >=300 | ||
---|---|---|---|
Yield strength | |||
Tensile strength Rm (N/mm2) | 750 | ||
Elongation A5 (%) | 30-35 | ||
ISO-V notch Impact energy (transvers) (J/cm2) (longitudinal) (J/cm2) | >= 100 <=150 | ||
Remarks |
Temparature information
Application area | ||
---|---|---|
Operation temperature | -321 ºF to 2012 ºF | good resistance to oxidation and carbonisation |
Explanation report | recommended up to 2000°F |
Solution heat treatment | ||
---|---|---|
Working temperature | 2102 ºF to 2192 ºF | water cooling |
Stress relief annealing | ||
---|---|---|
Working temperature | ºF to 1598 ºF |
Solution heat treatment | ||
---|---|---|
Working temperature | 2192 ºF to 1742 ºF | cooling with air/water |
Standards / information
Standards | Desciption |
---|---|
ASTM B 166 | Standard Specification for Nickel-Chromium-Cobald-Molybdenium Alloy rods,bars and wires |
ASTM B 167 | Standard Specification for .... NI-Cr-Fe-alloy seamles pipes and tubes |
ASTM B 168 | Standard Specification for.... Nickel-Chromium-Cobald-Molybdenium Alloy sheet metal and ribbons |
ASTM B 366 | Standard Specification for Factory-Made Wrought nickel and nickel alloy fittings |
ASTM B 564-06 | Standard Specification for Nickel Alloy Forging |
DIN 17744 (2002/09) | nickel-forgeable alloy with molybdenum and chrome |
DIN 17750 (2002/09) | ribbons and sheet metal out of nickel with nickel-wrought alloy properties |
DIN 17751 (2002/09) | tubes out of nickel with nickel-wrought alloy properties |
DIN 17752 (2002/09) | rod made from nickel with nickel-wrought alloy properties |
DIN 17753 (2002/09) | wire out of nickel with nickel-wrought alloy properties |
DIN EN 10088-1 (09/2005) | Stainless steels Part 1: List of stainless steels |
DIN EN 10302 | heat-resisting steel nickel-cobalt alloy |
VdTÜV-Werkstoffblatt 485 | extremely heat-resisting nickel based alloy, NiCr23Co12Mo, material-nr. 2.4663; ribbon, sheet metal, rod, forging, seamless pipe |
VdTÜV / Werkstoffblatt 485 | extremely heat-resistant nickel based alloy, NiCr23Co12Mo, material-nr. 2.4663 ribbon, sheet metal, rod, forging, seamless pipe |
Process information
Cold forming | good forming |
---|
Chip removing process | in solution annealed state (mind cold-work forming), good mechanical processing properties |
---|
Welding | |
---|---|
- Type | well weldable |
- Add. material | welding rods: 2.4627; covered rod electrode: 2.4628 |
Main fields of application
Details of application | well suited for high temperatures with high mechanical demands |
---|---|
Certifications | |
Power engineering | burning chambers |
Power engineering | Teile im Hochtemperaturbereich (Brennkammern) |
Power engineering | heat exchanger for high temperatures |
Power engineering | pipes and tubes |
Chemische Industrie | wärmetechnische Anlagen |
petrochemical industry | thermotechnical plants |
Range of products
Product type | Product |
---|---|
Plates / Sheets | plates/sheets plate/sheet cuts |
Rotating components | fittings from barsteel |
Fittings | welded elbows welded reductions Welded T-pieces seamless elbows seamless reductions seamless T-pieces |
Flanges / Collars / Flared tube ends | flared tube end collars various flanges (weld neck flange,blind flange etc.) |
Pipes / Tubes | welded pipes/tubes welded square pipes/tubes seamless pipes/tubes |
Bar steel | flat steel section steel round bar steel |
Liability exclusion
All aforementioned specifications serve as a general orientation and have to be reviewed depending on the conditions of use.(c) 2012 M. Woite GmbH, Postbox, D-40671 Erkrath | Phone +49 (211) 24 40 91 - Fax +49 (211) 24 92 28 | www.m-woite.com - woite@woite-edelstahl.com